Check engine light is an advanced technology in modern vehicles that displays warning lights to inform the driver of minor or major system failures.
Minor in the sense that, those faults aren’t crucial and can be attended to some other time meanwhile a major problem is the one that’ll require the driver to stop immediately or even stop the car because of the impact.
It’s important to understand all warnings that’ll appear on your dashboard and know which action to take as provided in your car user manual.
Therefore, the question “how long can you drive with Check Engine Light ON” simply depends on the severity of the impact caused by the failure of your vehicle.
In this article, you’re going to learn what the check engine light is, how to diagnose the error code and how long you can drive with the check engine light on.
Check Engine Light ON – Meaning
Check Engine light, sometimes known as the Malfunction Indicator Light (MIL), is a warning light that illuminates whenever the Engine Control Module detects a problem (ECU). The majority of a modern car’s functionality depends on sensors and actuators that monitor and enhance engine performance.
The ECU is coupled to these sensors and controllers. The manufacturer pre-programs the car’s ECU with certain values. The check engine light turns on to alert the driver that something is off when the ECU detects an erroneous (high/low) number.
Although, the check engine light turns on when you Ignite your car and goes off after some time if it doesn’t find any error.
However, if the check engine light still remained ignited then you should check out for signs such as stalling, unusual sounds, or fuel consumption.
The ECU in turn stores a diagnostic troubleshooting error code that can now be read using a diagnostic scanner.
The On-Board Diagnostics (OBD2) port, which is typically found under the steering wheel, is where the scanner is attached to the vehicle. The mechanic can identify which sensor or actuator is causing the vehicle to malfunction by scanning the vehicle with a diagnostic instrument.
Some of the common reasons why the check engine light usually turns on include;
- An issue with the spark plugs
- An ignition coil error
- A problematic Mass Airflow Sensor
- A defective oxygen sensor
- A faulty fuel injector etc.
You can visit our error codes page to check out possible codes that might be stored by the OBD-II scanner and how to fix them.
How Long Can I Drive with Check Engine Light On?
As discussed earlier, This question’s response is a little unclear. Everything relies on how serious the problem was that caused the light to turn on. Before deciding whether you can drive with the engine warning light on or not, you need to perform some inspections.
You can simply check out for indications from all indicator lights. Turn OFF the vehicle and turn it back on while observing its response.
Furthermore, you can reduce the speed of the car, and remove any heavy load from the vehicle, If the check engine light is illuminated immediately after refilling, the fuel cap should be thoroughly tightened, etc.
However, if the check engine light turns on without showing any effect on your vehicle’s performance, it’s safe to continue driving but you must take the car to a mechanic to resolve the issue.
In addition, disconnection between the wiring harness between the engine control module and the sensors might have been tampered with thereby leaving the light turned on.
Check Engine Light ON – How to Diagnose and Fix
Let me give you a brief guide on how you can decipher why your check engine light is illuminated and how to fix the issue.
You’ll need to purchase a diagnostic tool also known as the OBD-II scanner from Amazon (If you’re willing to do it on your own). We recommend the FOXWELL Car Scanner NT604 Elite OBD2 Scanner.
- Connect the OBD-II scan tool to your car’s OBD-II port after purchasing it (the port is located beneath the dashboard’s lower border on the driver’s side)
- To prevent bending any of the device pins, take caution when attaching the device.
- Turn the key to the “ON” option but leave the engine off
- The scanning tool may read the recorded codes from the ECU memory and flash a few LEDs.
- Now, from the menu, choose read codes and take note of the codes that come up on the screen, for example, P0123
You can now perform a Google search to know how to resolve it. (You can also check our error codes page)
You can now restart the car and see if the check engine light will be turned off and the error code cleared.
If you’ve done this and the lamp is still on, As quickly as you can, identify the broken part, fix it, or replace it. This is due to the possibility that the fault will reduce engine power and result in odd noises and vibrations. Additionally, it makes the car’s emissions worse. If certain problematic components, such as the catalytic converter, are not fixed, the head gasket may eventually blow.
It’s necessary that every car owner keep an eye on the check engine light in order to decipher when there’s a possible fault in the car system.
Using a diagnostic scanner will further increase your chances of resolving the issue and getting your car back to default.
Also, while some codes will require immediate attention; others will not and some error codes will clear off by themselves.
Whatever the case may be, do well to perform a routine check on your vehicle to prevent the emergency check engine light from turning ON.