Is your car key stuck in the ignition and you don’t know what to do? Well, this article is the right one for you as I will be teaching you why your keys are stuck in the ignition and how to remove the key stuck in the ignition.
Having your car key gets stuck in the ignition of your Chevy Cruze, or Subaru vehicle can be very stressful. Whenever your car key is in the ignition; it should be easy to remove after a complete counterclockwise rotation and a push on the key release button. If it doesn’t come out, do not attempt to use force to get it out as it could get broken in that process thereby causing a more serious problem.
In this article, you’ll learn why your key gets stuck in the ignition and how to remove a stuck key from the ignition.
Why is My Key Stuck in the Ignition?
If your car key won’t come out of the ignition, then there is a variety of reasons as to why that happened and you need to understand the possible cause of this problem so as to figure out a possible solution to it. These are some reasons your key could get stuck in the ignition;
Steering wheel lock
Turning off your vehicle while moving the steering wheel could activate the steering wheel lock. And this will not only prevent you from turning the steering wheel but also not allow you to remove the key from the ignition. This happened because the ignition cylinder locked at the same time the steering wheel locked.
Not setting gear to park
The transmission gear should always be in Park before you attempt to remove a car key from the ignition. If the gear is set to drive, neutral, or any other available gear, in an automatic transmission, then the key will not come out of the ignition. Sometimes, the gear does not fully set to park when people attempt to change the gear to park. However, ensure that “P” is highlighted after changing the gear to park if your vehicle has a digital screen display.
Your car keys wear a little each time you put them in the ignition and turn. Also, you subject your key to wearing each time you toss it around, especially on hard surfaces and this slowly damaged the key. The key could become tough and difficult to remove from ignition. Ensure the replacement of the key once you notice any damage.
A dead battery
The ignition system is dependent on the power from the battery for proper functioning therefore if the battery is dead then, it will likely cause the ignition system to lock up. Which won’t allow you to get the key out of the ignition. The only way out is to get a new battery installed.
A damaged ignition cylinder
An ignition lock cylinder that is damaged can make your key to be stuck in the ignition. This happens because there are several rows of spring-loaded pins inside of the ignition lock which matches up with the shape of your key when inserted and if for any reason these pins are slightly out of alignment, that can prevent the key from being removed.
Dirt on key
Sometimes people open boxes and packages using their car keys. This might effectively tear through the box tape, but could also leave pieces of the tape to stick to the key. And this may cause dirt to get attached to the key and if you were to place the key into the ignition of your vehicle, then it will be harder for the key to engage the ignition cylinder’s pins.
How to Remove Key Stuck in the ignition
These are some simple methods you could use to get a stuck key out of the ignition.
Shake the gear selector
You would not be able to remove the keys if your car has an automatic transmission unless the selector is properly set in neutral or park. A Gentle shake on the selector while in the park position could be the remedy for this issue most often.
Unlock the steering wheel
Most new vehicles come with a locking mechanism that is activated whenever the steering wheel is turned too far to the right or left. Turning the wheel in the opposite direction could help release the lock and allow the key to be removed.
Spray Lubricant Into the Ignition Lock
This is an alternative measure you can try if you are not entirely convinced that your old car key is to blame. However, this step only applies to keys that are not severely worn or damaged. Lubricate the lock using a spray bottle and a pipe. If that does not work then proceed with any of the other methods listed in this article. Also, you can spray a little amount of WD-40 or Dry Graphite lubricant inside the ignition keyhole once every six months as a preventive measure.
Jiggle the key
This is another easy method you could use to remove a stuck key. To do this, push down on the key cylinder with your left index finger while jiggling the key simultaneously with your right hand. This giggle will help to loosen the grasp of the springs and pins located inside the cylinder and the key would be allowed to slide out.
How long does it take to replace the ignition lock cylinder?
30 to 45 minutes, provided all the necessary replacement parts are available.
How do you know if your ignition lock cylinder is bad?
A failing ignition lock cylinder, just like other electrical and mechanical components in a car, will give some noticeable signs to the driver. These signs may include;
- No noise from the starter motor
- Trouble starting the vehicle
- Challenges when inserting and removing the ignition key
- Flickering dashboard lights.
You have seen the reasons for a key stuck in the ignition and how to remove it. So you do not need to get worried whenever you find yourself in a situation like this. Rather try any of the above steps when your car key is stuck in the ignition to get it removed. However, do not forget to contact your mechanic if all the steps prove abortive. Please share and drop your questions in the comment section.