How to Bypass Ignition Control Module

A malfunctioning car ignition system can be the reason why your car has refused to start when ignited. The truth is that it is possible for you to bypass the ignition control module and get your car started.

In this article, I would be teaching you how to bypass the ignition control module.

What are the symptoms of a faulty ignition control module?

Some symptoms that can be noticed when the ignition control module is faulty are

1. Misfiring or rough running of the engine: this occurs when there is incomplete combustion.

2. Ignition Timing: the ignition timing can be affected when the ignition control module is faulty.

3. The engine running low: the engine will not accelerate well and will run at a low speed.

How to Bypass the Ignition Control Module

Bypassing the ignition control module is not a simple task but depends strictly on the car model. You will need some mechanical tools to enable you to bypass the ignition control module of your car. There are different methods through which you can bypass the ignition control of your car and they include:

1. Hotwiring

This method is suitable for older models of cars and to do this you need to identify your car’s steering wheel column first. Then, open the plastic cover that conceals the ignition wires inside. After which you identify the connector which is located in the middle of the car steering column in most cars. Though this can be a bit difficult due to the number of wires inside. The yellow and brown wires are for the ignition while the red wires are related to the battery. Take the red wire that serves the battery and strip them down about one inch from the insulation then twist them.

Recommended:  Is Power Steering Fluid Flammable?

To bypass this ignition control module, you have to connect the on/off ignition wire of the car with the wire which connects to the battery which causes the car lights and electronics to come on. Then touch the starter wire to the wires connected to the battery to make the car engine start, thereby bypassing the ignition control module and starting the engine.

2. Jump Start the Car

This method of bypassing the ignition control module is reserved for people who are very familiar with the components under the hood well and can be done with the use of a portable jump starter or another vehicle to jump-start yours.

  • For this method, you must first identify the red coil wire to bypass the ignition control module.
  • The ignition coil and battery are located under the hood of your vehicle.
  • Connect the positive side of the coil to the positive terminal of the car battery.
  • The jump starter cable can also be connected to the coil that way, the dashboard could get the power required for the ignition of the engine.
  • Locate the starter solenoid inside the steering wheel column and connect it to the positive terminal of the car battery.
  • After which you will take the ignition wire out from the ignition control module.
  • Activate the solenoid and make the starter crank the car by connecting the solenoid’s positive terminal to the where ignition control switch is connected with a screwdriver.

That’s it

3. The use of a Drill And Screwdriver

This method can damage the ignition control module. To do this, you have to first locate the keyhole of the car and drill 2- 3 inches (depending on the length of your car key) into it using a metal drill. After which you remove the locking bits till they are in position. Or you can insert your screwdriver into the keyhole and use your hammer to hit it till the locking pins inside the ignition are broken. You can then insert a screwdriver into the keyhole and turn the ignition.

Recommended:  Brake Pad Wear Indicator - A Detailed Overview

FAQs

Can you bypass the ignition to start the car?

Yes, you can bypass the ignition by using a portable jump starter or by jump-starting your vehicle with another.

Can you bypass the ignition immobilizer?

Yes, and You can bypass the ignition immobilizer by placing the key in the keyhole thereby deactivating the car’s immobilizer to remote start.

What is the ignition bypass wire?

The ignition bypass wire is a wire which prevents the ignition coil from sending power to the starter while running the engine.

Where does the ignition get power from?

Battery, which is part of the engine ignition system. This starts with the ignition coil, which gets power from the battery and turns it into a spark that is powerful enough to ignite fuel vapor.

Conclusion

If you ever find yourself in a situation where you need to bypass Ignition Control Module. These methods of bypassing the ignition control module that I have shared in this article should help you do so.

How helpful was this post?