How to Get Air Out of Brake Lines Without Bleeding

This article entails how to get air out of brake lines without bleeding… continue reading.

The brake system of a car is one of the most important safety features of a car. The brake system transfers the force from your foot on the pedal to the wheels using fluid pressure. And if air enters into this fluid stream, it causes the high-pressure sections not to compress as much as needed for safe braking thereby posing a problem. Therefore it is very important to keep air bubbles out of the brake lines because it could affect its efficiency and performance.

You might be a do-it-yourself kind of person and need a way to get air out of the brake lines without bleeding. If so, then this article is the right one for you as I will give you a guide on how to get air out of brake lines without bleeding.

Why do you need to remove air from your brake lines?

You need to remove air from your brake lines because the responsiveness of your brakes reduces once there is air in the brake lines. This can be dangerous, especially while driving on busy highways or when you suddenly get obstructed by an object on the road while you’re driving because your brakes will become progressively worse, making it even more dangerous to drive.

Recommended:  How to Fix Car Light Dimming and Brightening

So, removing air from your brake lines will restore proper pressure and responsiveness to your car’s brake so that it’ll respond quicker and faster when applied.

Causes of Air Bubbles brake lines

Air can get into the brake lines of your vehicle through the following means:

1. An air bubble is created when a porous brake line gets in contact with another part of the brake system. And even small amounts of trapped air create bubbles in your brakes’ hydraulic systems as pressure from your foot on the pedal squeezes the fluid and air together.

2. Air bubbles could also be created if the old fluid was not completely bled out of your car system during a brake job.

3. Some brake fluids absorb water over time, especially when regularly used during cold weather, and this can create air bubbles when refilled with fresh fluid

Symptoms of Air in the Brake Lines

There are some obvious signs that tell you that you have air in your brake lines. The signs include:

1. Ineffective Brakes: Brakes won’t work when depressed.

2. Spongy Brake Pedal: this is when the brake pedal feels spongy when pressed down.

3. Loose Brake Pedal

How To Get Air Out Of Brake Lines Without Bleeding

To get air out of the brake lines of your vehicle, you have to take the following steps:

  • Get your car on a flat surface and apply the parking brake.
  • Open the hood of the vehicle and locate the master cylinder reservoir cap which is octagonal or cyclically shaped and has an arrow that points to which wheel should be pumped first.
  • Turn the reservoir cap in an anticlockwise manner until it completely comes off.
  • Clean the cap and place it back on the reservoir making sure the arrow is pointing at which wheel should be pumped first. And repeat for the remaining three wheels, so all the reservoir has their own cap with an arrow pointing to them.
  • Then step slowly on each brake pedal for as much time as possible until it becomes firm again or until air comes out no more.
  • Remove the reservoir cap from any of the master cylinders and slowly pour in fresh brake fluid until it gets below the brim of the tank. While doing this, ensure that there are no air bubbles in the liquid by tilting the container slightly to enable them to rise to the top. Do this for the other master cylinders, if necessary.
  • Start the engine of your car and press on each brake pedal to push out any excess air from the system. Do this many times until each brake pedal feels firm again, then test the brake to see if the work properly and stop the engine.
Recommended:  How to Fix Car Heater Blowing Cold Air

That’s it.

FAQs

Will Air Work Itself Out of Brake Lines?

No, the air inside the brake lines would not just go out on its own. Rather the problem could get worse because a bunch of small air bubbles in the line might eventually come together to become one big, dangerous bubble. As a result, your brakes would not have their normal pressure and could fail at any time.

How long does it take to get air out of brake lines?

45minutes to 1 hour, depending on the severity of your braking system. To bleed a brake, you must first locate the brake line vehicle under the car before the actual task of brake bleeding can begin.

How do I Get the Pressure Back in my Brakes?

Close the bleeder screw and pump up the pressure bleeder after the fluid stops flowing. Then crack the screw open again to allow more fluid to flow out, do this over and over again until the fluid comes out clean.

Should the engine be running when bleeding brakes?

No. The engine of your vehicle shouldn’t be on or running while bleeding the brakes. It would be easier to push down the pedal if the car is running because of the power brakes but not necessary while bleeding the brakes.

Do I need to bleed all 4 brakes?

Yes, car experts recommend that you bleed all four brakes once you open one of the brake lines to replace a caliper. Although this is not compulsory provided the brake line being worked on is not dependent on any of the other lines.

Recommended:  Key Stuck in Ignition? Here's What to Do

What is the best brake bleeding method?

The reverse bleeding method is considered the best single-brake bleeding method to use. It is very effective at removing trapped air and works well with vehicles with a bleed screw as well as ABS-equipped vehicles.

Conclusion

The brake system of a car is one of the most important safety features of a car. And when there is air in the brake lines, the braking action becomes ineffective and could be very dangerous. I believe the above guide will enable you to get the brake system to work properly and safely.