P0341 Code – Meaning, Causes, Symptoms and How to Fix it

This article will show you all you need to know about the P0341 code, its causes, symptoms, and possible fixes you can lay your hands on.

The P0341 code is a diagnostic trouble code that is triggered when the camshaft position sensor is not correlating with the signals from the crankshaft position sensor.

The P0341 code can simply be described as a Camshaft Position Sensor Circuit Range/Performance whereby the sensor is returning an abnormal signal to the PCM (Power Control Module)

What could cause an Error P0341 Code?

One or either of these could result in triggering the error P0341 code in your check engine light.

  • A low or faulty car Battery
  • Poor Wiring between the sensor and PCM
  • Malfunctioning Starter Motor
  • A faulty camshaft position sensor
  • The camshaft sensor responds slower than the crankshaft sensor

This error code can easily be fixed seeing that most of the causes can be resolved without the presence of an auto mechanic, well, not all causes though.

What are the Symptoms of the error P0341 Code?

Below are some symptoms to watch and check out to know you ran into error P0341 and not some regular OBD-II trouble code.

  1. The check engine light will light up
  2. The engine will hard start
  3. The vehicle won’t respond at all
  4. Misfiring or jerking or vehicle
  5. Low Power in the engine if it eventually starts.
  6. Irregular power through the RPM range
Recommended:  7e8 Engine Code: All you Need to Know

How to Fix the Error P0341 Code

Here are some fixes you can resort to repair the code P0341 error on your vehicle.

  1. Faulty Camshaft replacement
  2. Battery replacement
  3. Repairing the wiring and connector for the camshaft sensor
  4. Fix the broken reluctor ring on the camshaft gear

What Damage can Error P0341 Cause?

All error code displayed on the check engine light requires immediate attention so do the P0341 code.

Aside from the continuous jerking, misfiring, and poor engine performance, the OBD-II error code can cause the engine not to respond on start.

Highlighted below are some of the damages that might be incurred to your vehicle if not resolved as soon as possible.

  • The engine will stop responding
  • Poor engine performance
  • Misfiring while driving
  • Everything said as the symptoms above.

How to Diagnose the Error P0341 Code

There are certain troubleshooting that should be done by a mechanic before coming to the conclusion that your vehicle ran into an error P0341 code. Here’s a tip for running a diagnosis

  1. Scan the code with a code reader or scanner
  2. Clear the engineer
  3. Perform a road test while checking out for noticeable defects
  4. Check the wiring and connection to the camshaft sensor
  5. Tighten and replace damaged or loosed connections respectfully
  6. Disconnect and check the resistance and voltage from the camshaft sensor
  7. Check for rusts in the sensor connection
  8. Check for breakage of the camshaft or the camshaft gear.
  9. Install a new Sensor


How can I reset a camshaft position sensor?

Regrettably, there’s no known way to reset the camshaft position sensor. So the only way around it is to get complete camshaft position sensor replacement parts.

Recommended:  Error P0200 Code: What could Cause P0200 code and Fixes

Can you drive with code P0341?

No, it isn’t advisable to continue driving when your vehicle run into an error P0341 code due to frequent shuttering and shutdown of your car’s engine.

In most cases, your vehicle might even refuse to respond thereby causing traffic to other road users, so, it’s best to park your car at a corner and fix the code P0340 code before hitting the road again.

How long does it take to fix a camshaft position sensor?

A typical camshaft position sensor replacement or fix takes between 1 hour to 2 hours to be completed although it depends on the model of your vehicle.

Will a car start without a camshaft sensor?

No, as we discussed earlier, the camshaft sensor is used by the PCM to control the fuel injectors and spark plug ignition. Without the camshaft position sensor present, your vehicle will not start.

Codes related to P0341 Code

The P0341 code goes hand in hand with the P0342 and P0343 error codes which signify low and high signals respectively.

If you encounter the 3 error codes at a time on your dashboard once then you’ll need to reach out to an electrical engineer to resolve it.


The error P0341 code should be resolved as soon as they show up to curb it from causing more damage to the engine of your vehicle.

You can try any of the listed fixes above and the error P0341 code should disappear instantly.