Park Assist Blocked – Meaning and Solutions

It’s knowledgeable that most modern cars come equipped with new technologies that make driving easier – The park assist feature is one of them.

The park assists will enhance your parking experience by helping you go in and out of a parking space.

You don’t have to deal with finding a parking space since the parking assistant will find a convenient spot and direct you on what to do (braking and acceleration), and in most cases, it takes control of the wheel, for example, Modern-day Mercedez Benz.

However, there are times when you’ll summon the park assistance and you will get a park assist Blocked message on the DIC. Don’t fret, car systems are prone to failure at times.

And you know the troubles that come with manual parking (to and fro movement) especially in tiny spaces – thanks to technology.

In this article, I’ll further explain what it means if your park assist got blocked, why it got blocked, and how to Reset a blocked park assist.

What does a Park Assist Blocked message mean?

The park assists technology is a feature that comes with modern-day cars that aid in finding a parking spot, giving directions, and parking the car in some cases. Information regards the status of your park assist will be displayed on your dashboard.

For Instance, a Silverado whose park assist is blocked will display a “park assist block’ notification on its dashboard to signify a fault or malfunctioning in the park assist.

Recommended:  6 Symptoms of a Bad Speed Sensor

While some models will come up with the ‘Park Assist blocked read owner’s manual’ notice on the driver information center (DIC). If you often use this feature then you’ll need to get your car to an auto repair shop as soon as possible.

Notwithstanding, you can check out some Do-it-yourself tips that you can test-run before consulting a mechanic.

Reasons why Park Assist gets Blocked

One or more of the below factors are the major cause of a failed or blocked park assist.

  1. Presence of Dirt and Debris
  2. Faulty Park assist sensor
  3. An issue in the wiring harness of the Park assist
  4. Extreme weather conditions
  5. Driving at high speed
  6. Towing Vehicles
  7. Problematic PCM

A Park assistant covered in dirt or debris due to driving off-road or not properly washing your vehicle might not function properly.

Also, Extreme weather conditions might cause ice or snow to cover the Park assist making it either fail or stop responding.

In addition, don’t expect the Park assistant to work when trying to park at a very high speed, except if you’re in haste or you’re an armed robber I don’t see reasons why you should park at a very high speed. It could also save you from bashing your vehicle.

Since the park assists are mostly attached at the rear or back bumpers, making use of a towing vehicle might default the installed park assist.

Finally, since the PCM is the overall brain of the vehicle, a malfunctioning one can cause it to stop receiving signals from the park assists even when everything is fine.

Once the above factors are addressed then your park assist will surely come back to life.

Recommended:  How Long Does An Oil Change Take

continue reading to find out how to test and unblock a park assist sensor.

How to Test a Park Assist Sensor

While a faulty park assist sensor could be a complex issue that’ll require the service of a mechanic, it’s important that you run some background fixes that might fix the issue and save yourself the cost. Remember to first check the DIC for a “Park Assist Faulty” warning.

If you follow the steps outlined in this article, you should be done testing the sensor within two hours; you could also opt-in for numerous tests before making a conclusion.

The steps are listed below.

  • Remove all your parking assist sensors
  • Switch your multimeter to 2000k ohms
  • Place the multimeter on pin 1 and Pin 2 terminal pins on the sensor and take your results
  • Switch the multimeter to 20k ohms
  • Test both pins again
  • You should get a reading between 10 as the test result.

If no outputs came out on either 2000k or 20k then the park assist has been blocked. However, if the sensor(s) reads 800 to 900 on a 2000k setting and below 9.7 on 20k then you’ll need to get a sensor replacement as soon as possible.

How to Unblock Park Assist

The best guide for unblocking a park assist is with your car manufacturer, you can also check your car manual if you will be provided with an unblocking technique, or better still; contact your manufacturer.

Nevertheless, here’s a guide for Honda and Acura car owners, you could also implement it and see if it unblocks park assist on your vehicle.

  1. Turn your ignition ON
  2. Continuously tap the park assist button at least 10 times
  3. Turn the vehicle ignition OFF
  4. Tap and hold on the park assist button
  5. Switch on the vehicle while the park assist button is still pressed down
  6. Wait some time and see if it responds.
Recommended:  Common Bad CV Joint Symptoms

You should get a beep sound twice to notify you that the reset action is a success, if the reverse is the case then you should take your vehicle to an auto technician.

PARK ASSIST FAQs

Q: Where is the Park Assist sensor located?

The park sensors are located on the front and the back bumper of your car. It helps make parking easier by identifying objects 4 feet in front and 8 feet behind the car. The park assist can be disabled by tapping the park assist button, using the setting menu, or turning the steering.

Q: How do I Clean the Park Assist sensor

You can use a neat damp cloth to clean the parking sensors. Simply get a cloth, immerse it in water, squeeze it and use it to gently wipe the sensors.

Q: How do I turn my park assist back on?

The park assist has a specialized button on your car dashboard that can be used to enable or disable the feature by toggling ON and OFF respectively.

If you don’t find the park assist button on your car then you can consult your manufacturer’s guide or there might also be a probability that park assist isn’t available for your car.

Conclusion

A faulty park assist (sensor) can frustrate the driver especially when it shows up unannounced.

If you’ve tried the above fixing guide and the problem persists then take your vehicle to an auto repair shop.